本論文在積體化被動元件製程上實現微型化之帶通濾波器設計，此設計特色為藉由此先進半導體製程非常適於發展高線圈纏繞密度之變壓器結構，並搭配耦合諧振器方法用以設計面積極微小化的單頻與雙頻帶通濾波器，並採用電磁抵銷機制與外加迴授路徑的設計方法於帶通濾波器之頻率響應產生傳輸零點，用以提升濾波器的頻率選擇性與增強禁帶抑制能力。而帶通濾波器之通帶的頻率選擇性除了可用傳輸零點來提升外，其本身諧振器具有較高的非負載品質因子時也會有較好的頻率選擇性。為了滿足手機端通訊產品對帶通濾波器之通帶頻率選擇性的高規格要求，本論文亦採用具低損耗的RT/Duroid基板設計一具高品質因子之諧振器，並搭配交錯耦合的三階帶通濾波器結構於極近通帶的頻率位置產生一額外的傳輸零點來滿足此嚴謹的商用規格需求。

This thesis realizes miniature bandpass filters using integrated passive device technology. The bandpass filters are designed based on coupled resonator method with single-band and dual-band responses, using a transformer structure with high-density winging pattern. In addition, the designs adopt the electric- and magnetic-field cancellation and the feedback mechanism to produce transmission zeros in the filter responses for enhancing selectivity and stopband rejection. In order to satisfy the specific requirements of commercial bandpass filter products, this thesis designed and implemented a trisection filter with cross coupling on a low-loss RT/Duroid substrate to generate a transmission zero very near the passband.

論文審定書 i
致謝 ii
論文基本資料 iv
摘要 v
Abstract vi
目錄 vii
圖目錄 ix
表目錄 xii
第一章 緒論 1
1.1 研究動機 1
1.2 文獻探討 2
1.3 章節內容概述 3
第二章 實現於IPD之單頻帶通濾波器設計 5
2.1 IPD製程介紹 5
2.2 以平面型變壓器為基礎之帶通濾波器設計 6
2.2.1 基本濾波器合成理論 6
2.2.2 電路設計 12
2.2.3 模擬與量測結果 15
2.3 雙模諧振之帶通濾波器設計 20
2.3.1 雙模態諧振之設計理論 20
2.3.2 並聯回授路徑機制 24
2.3.3 電路設計 26
2.3.4 模擬與量測結果 28
第三章 實現於IPD之雙頻帶通濾波器設計 31
3.1 雙頻帶通濾波器設計 - Type I 31
3.1.1 電路分析與設計 31
3.1.2 模擬與量測結果 37
2.3雙頻帶通濾波器設計 - Type II 40
3.2.1 電路分析與設計 40
3.2.2 模擬與量測結果 46
第四章 三階交錯耦合帶通濾波器設計 49
4.1 多層印刷電路基板介紹 49
4.2 基本理論 50
4.3具低旁帶傳輸零點之三階帶通濾波器設計 53
4.3.1電路架構分析 53
4.3.2 模擬與量測結果 56
4.4具高旁帶傳輸零點之三階帶通濾波器設計 60
4.4.1電路架構分析 60
4.4.2 模擬與量測結果 63
第五章 結論 67
參考文獻 68

參考文獻
[1] K. Liu, R. C. Frye, B. Ahn, “High rejection BPF for WiMAX applications from Silicon Integrated Passive Device technology,” in IEEE MTT-S Int. Microw. Symp. Dig., 2010, pp. 1364-1367.
[2] C.-W. Tang, C.-W. Shen and C.-C. Tseng, “Broadband cascade quadruplet bandpass filter with low-temperature co-fired ceramic technology,” IEEE Microw. Wireless Comp. Lett., vol. 17, no. 5, pp. 340-342, May. 2007.
[3] Y.-S. Dai, W.-K. Zhou, B.-S. Li, D.-L. Lu, S.-L. Xiao, J. Zhang, G.-Q. Fu, Y.-F. Yao, Y.-H. Guo, S.-B. Chen and L.-J. Wang, “Design and implementation of an miniaturized LTCC filter with high stopband rejection,” in Proc. Int. Conf. on Microw. and Millimeter Wave Technology, 2010, pp. 1584-1587.
[4] C.-H. Chen, C.-H. Huang, T.-S. Horng, S.-M. Wu, J.-Y. Li, C.-C. Chen, C.-T. Chiu and C.-P. Hung, “Very compact stacked LC resonator-based bandpass filters with a novel approach to tune the transmission zeros,” IEEE Microw. Wireless Comp. Lett., vol. 19, no. 5, pp. 293-295, May. 2009.
[5] H. Wang and Q.-X. Chu, “An EM-coupled triangular open-loop filter with transmission zeros very close to passband,” IEEE Microw. Wireless Comp. Lett., vol. 19, no. 2, pp. 71-73, Feb. 2009.
[6] Q.-X. Chu and H. Wang, “A compact open-loop filter with mixed electric and magnetic coupling,” IEEE Trans. Microw. Theory Tech., vol. 56, no. 2, pp. 431-439, Feb. 2008.
[7] P.-H. Deng, Y.-S. Lin, C.-H. Wang and C.-H. Chen, “Compact microstrip bandpass filters with good selectivity and stopband rejection,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 2, pp. 533-539, Feb. 2006.
[8] J.-T. Kuo, W.-H. Hsieh and M. Jiang, “Design of two-stage UIR and SIR bandpass filters with an elliptic function-like response,” in IEEE MTT-S Int. Microw. Symp. Dig., 2004, pp. 1609-1612.
[9] C.-L. Hsu and J.-T. Kuo, “Design of cross-coupled quarter-wave SIR filters with plural transmission zeros,” in IEEE MTT-S Int. Microw. Symp. Dig., 2006, pp. 1205-1208.
[10] Y.-M. Chen and S.-F. Chang, “A compact stepped-impedance pseudo-interdigital bandpass filter with controllable transmission zero and wide stopband range,” in Proc. Eur. Microw. Conf., Sept. 2009-Oct. 2009, pp. 783-786.
[11] X. Guan, F. Wen, C. Wang, S. Jiang and H. Liu, “A cross-shaped stepped-impedance resonator bandpass filter with wide stopband,” in Proc. Int. Conf. on Microw. and Millimeter Wave Technology, 2010, pp. 574-576.
[12] C.-W. Tang amd H.-H. Liang, “Parallel-coupled stacked SIRs bandpass filters with open-loop resonators for suppression of spurious responses,” IEEE Microw. Wireless Comp. Lett., vol. 15, no. 11, pp. 802- 804, Nov. 2005.
[13] Y.-C. Chiou, Y.-F. Lee, J.-T. Kuo and C.-C. Chen, “Planar multimode resonator bandpass filters with sharp transition and wide stopband,” in IEEE MTT-S Int. Microw. Symp. Dig., 2008, pp. 439-442.
[14] Y.-C. Chiou, J.-T. Kuo and E. Cheng, “Broadband quasi-Chebyshev bandpass filters with multimode stepped-impedance resonators (SIRs),” IEEE Trans. Microw. Theory Tech., vol. 54, no. 8, pp. 3352-3358, Aug. 2006.
[15] U.-H. Lok, Y.-C. Chiou and J.-T. Kuo, “Quadruple-mode coupled-ring resonator bandpass filter with quasi-elliptic function passband,” IEEE Microw. Wireless Comp. Lett., vol. 18, no. 3, pp. 179-181, Mar. 2008.
[16] M. Zhou, X. Tang and F. Xiao, “Miniature microstrip bandpass filter using resonator-embedded dual-mode resonator based on source-load coupling,” IEEE Microw. Wireless Comp. Lett., vol. 20, no. 3, pp. 139-141, Mar. 2010.
[17] Y.-F. Lin, C.-H. Chen, K.-Y. Chen, H.-M. Chen and K.-L. Wong, “A miniature dual-mode bandpass filter using Al2O3 substrate,” IEEE Microw. Wireless Comp. Lett., vol. 17, no. 8, pp. 580-582, Aug. 2007.
[18] Z. Ma, H. Sasaki, C.-P. Chen, T. Anada, Y. Kobayashi, “Design of a wideband bandpass filter using microstrip parallel-coupled dual-mode ring resonator,” in Proc. Asia Pacific Microw. Conf., 2008, pp. 21-24.
[19] M.-L. Hsieh, L.-S. Chen, S. Wang and S.-L. Fu, “Microstrip cross-coupled trisection bandpass filters fabricated on high dielectric constant ceramic substrates,” in Proc. Int. Conf. on Electronic Materials and Packaging, 2006, pp. 1-4.
[20] A. Rahman, A. B., E. Dein, A. Z., Hamed, H. F. A., Ibrahim and A. A., “Small size third order coupled resonator band-pass filter using capacitor loaded slots,” in Proc. Middle East Conf. on Antennas and Propagation, 2010, pp. 1-4.
[21] J.-S. Hong and M. J. Lancaster, “Microstrip cross-coupled trisection bandpass filters with asymmetric frequency characteristics,” IEEE Proc. Microw. Antennas and Propagation, vol. 146, no. 1, pp. 84-90, Feb. 1999.
[22] E. Hanna, P. Jarry, E. Kerherve, J. M. Pham, “Cross-coupled suspended stripline trisection bandpass filters with open-loop resonators,” in IEEE MTT-S Int. Microw. Symp. Dig., 2005, pp. 42-46.
[23] M.-L. Hsieh, L.-S. Chen, S. Wang and S.-L. Fu, “Microstrip cross-coupled trisection bandpass filters fabricated on high dielectric constant ceramic substrates,” in Proc. Int. Conf. on Electron. Materials and Packaging, 2006, pp. 1-4, Dec. 2006.
[24] J.-M. Yook, J.-I. Yu, J.-C. Park and Y.-S. Kwon, “Balanced BPFs implemented using IPD (integrated passive devices) technology,” in Proc. Eur. Microw. Conf., 2010, pp. 429-432.
[25] R. C. Frye, K. Liu and Y. Lin, “Three-stage bandpass filters implemented in silicon IPD technology using magnetic coupling between resonators,” in IEEE MTT-S Int. Microw. Symp. Dig., 2008, pp. 783-786.
[26] S. P. Lim and J. Y. Park, “Compact WiMAX filter with three independent transmission zeros using PCB embedded passive technology,” in IEEE MTT-S Int. Microw. Symp. Dig., 2009, pp. 1065-1068.
[27] S. Zhuang, Y. Qin, K. Liu and G. Zhu, “LTCC bandpass filter with transmission zeros using grounding inductor for RF applications,” IEEE Int. Symp. on Antennas Propagation and EM Theory, 2010, pp. 1120-1123.
[28] H. Gan, D. Lou and D. Yang, “Cross-coupled microstrip bandpass filter using folded tapered-line resonators,” in Proc. Asia Pacific Microw. Conf., 2005, pp. 3.
[29] C.-M. Rao, T.-J. Wong and M.-H. Ho, “A parallel doubly coupled dual-band bandpass filter,” in IEEE MTT-S Int. Microw. Symp. Dig., 2006, pp. 511-514.
[30] M. Jiang, L.-M. Chang and A. Chin, “Design of dual-passband microstrip bandpass filters with multi-spurious suppression,” IEEE Microw. Wireless Comp. Lett., vol. 20, no. 4, pp. 199-201, Apr. 2010.
[31] M.-Q. Zhou, X.-H. Tang and F. Xiao, “Design of compact dual band bandpass filter with controllable bandwidths and good selectivity,” in IEEE MTT-S Int. Microw. Symp. Dig., 2008, pp. 145-148.
[32] M.-H. Weng, H.-W. Wu and Y.-K. Su, “Compact and low loss dual-band bandpass filter using pseudo-interdigital stepped impedance resonators for WLANs,” IEEE Microw. Wireless Comp. Lett., vol. 17, no. 3, pp. 187-189, Mar. 2007.
[33] S. Gao, H.-H. Hu and Z.-Y. Xiao, “A novel compact dual-band bandpass filter using SIRs with open-stub line,” 2008 China-Japan Joint Microwave Conference, pp. 464-466.
[34] C.-F. Chen, T.-Y. Huang and R.-B. Wu, “Design of dual- and triple-passband filters using alternately cascaded multiband resonators,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 9, pp. 3550-3558, Sept. 2006.
[35] S. Sun and L. Zhu, “Novel design of dual-band microstrip bandpass filters with good in-between isolation,” in Proc. Asia Pacific Microw. Conf., 2005, pp. 4.
[36] J.-T. Kuo and T.-W. Lin, “Dual-mode dual-band ring resonator bandpass filter with transmission zeros,” in Proc. Asia Pacific Microw. Conf., 2010, pp. 1865-1870.
[37] B.-C. Choi, W.-S. Lee, H.-C. Kim and H.-C. Cho, “A dual-band bandpass filter using a dual-mode ring resonator with two short-circuited stubs,” in Proc. Mediterranean Microw. Symp., 2010, pp. 152-155.
[38] S. Luo, L. Zhu and S. Sun, “A dual-band ring-resonator bandpass filter based on two pairs of degenerate modes,” IEEE Trans. Microw. Theory Tech., vol. 58, no. 12, pp. 3427-3432, Dec. 2010.
[39] Y.-C. Chiou, C.-Y. Wu and J.-T. Kuo, “New miniaturized dual-mode dual-band ring resonator bandpass filter with microwave C-Sections,” IEEE Microw. Wireless Comp. Lett., vol. 20, no. 2, pp. 67-69, Feb. 2010.
[40] P.-Y. Hsieh, Y.-C. Chiou, J.-T. Kuo and U H. Lok, “Compact hairpin resonator bandpass filters with dual-band response and wide upper stopband,” in Proc. Asia Pacific Microw. Conf., 2009, pp. 917-920.
[41] L. Wang, C. Zhao, C. Li and X. Lin, “Dual-band bandpass filter using stub loaded resonators with multiple transmission zeros,” IEEE Int. Symp. on Antennas Propagation and EM Theory, 2010, pp. 1208-1211.
[42] X. Y. Zhang, C. H. Chan, Q. Xue and B.-J. Hu, “Dual-band bandpass filter with controllable bandwidths using two coupling paths,” IEEE Microw. Wireless Comp. Lett., vol. 20, no. 11, pp. 616-618, Nov. 2010.
[43] X. Y. Zhang, J.-X. Chen, Q. Xue and S.-M. Li, “Dual-band bandpass filters using stub-loaded resonators,” IEEE Microw. Wireless Comp. Lett., vol. 17, no. 8, pp. 583-585, Aug. 2007.
[44] H. Lakdawala, X. Zhu, H. Luo, S. Santhanam, L. R. Carley and G. K. Fedder, “Micromachined high-Q inductors in a 0.18-μm copper interconnect low-k dielectric CMOS process,” IEEE J. Solid-State Circuits, vol. 37, no. 3, pp. 394-403, Mar. 2002.
[45] S.-M. Su, S.-M. Wu, C.-C. Lai, Y.-C. Tai, W.-Y. Lin and S.-W. Guan, “Analysis and modeling of IPD for spiral inductor on glass substrate,” in Proc. Int. Conf. on Microw. and Millimeter Wave Technology, 2008, pp. 1274-1277.
[46] G. L. Matthaei, L. Young, and E. M. T. Jones, Microwave Filters, Impedance-Matching Networks, And Coupling Structures, Norwood, Massachusetts: Artech House, 1980, pp. 149-155.
[47] J. S. Hong and M. J. Lancaster, Microstrip Filters for RF/Microwave Applications, 2nd ed., New York: Wiley, 2001
[48] M. Makimoto and S. Yamashita, Microwave Resonator and Filters for Wireless Communication, Berlin, New York: Springer, 2001。
[49] Z.-F. Zong, Y.-L. Qin, F.-L. Zhu and Y.-J. Zhao, “Analysis of second-order LTCC bandpass filter with two finite transmission zeros,” in Proc. Global Symp. Millimeter Waves, Apr. 2008, pp. 37-39.
[50] C.-F. Chang and S.-J. Chung, “Bandpass filter of serial configuration with two finite transmission zeros using LTCC technology,” IEEE Trans. Microw. Theory Tech., vol. 53, no. 7, pp. 2383-2388, Jul. 2005.
[51] S. Sakhnenko, D. Orlenko, K. Markov, A. Yatsenko, B. Vorotnikov, G.. Sevskiy, P. Heide and M. Vossiek, “Low profile LTCC balanced filter based on a lumped elements balun for WiMAX applications,” in IEEE MTT-S Int. Microw. Symp. Dig., Jun. 2008, pp. 1111-1114.
[52] L.-K. Yeung and K.-Li. Wu, “A compact second-order LTCC bandpass filter with two finite transmission zeros,” IEEE Trans. Microw. Theory Tech., vol. 51, no. 2, pp. 337-341, Feb. 2003.
[53] H. Nam, T.-S. Yun, H.-W. Lee, B.-K. Jeon, B.-W. Jeon, Y.-W. Kim and J.-C. Lee, “Compact bandpass filter with two transmission zeros using dual-mode microstrip resonator and tapped-line geometry,” in IEEE Int. Symp. on Commun. and Information Technology, Sept. 2009, pp. 1568-1571.
[54] C.-H. Kim and K. Chang, “Ring resonator bandpass filter with switchable bandwidth using stepped-impedance stubs,” IEEE Trans. Microw. Theory Tech., vol. 58, no. 12, pp. 3936-3944, Dec. 2010.
[55] M.-H. Weng, S. Wu, S.-B. Jhong, Y.-C. Chang and M.-S. Lee, “A novel compact dual-mode filter using cross-slotted patch resonator for dual-band applications,” in IEEE MTT-S Int. Microw. Symp. Dig., 2007, pp. 921-924.
[56] T.-L. Hsu, Y.-C. Chen, H.-C. Tseng, V. Liang and J. S. Jan, “psub guard ring design and modeling for the purpose of substrate noise isolation in the SOC era,” IEEE Electron Device Letters, vol. 26, no. 9, pp. 693- 695, Sept. 2005.
[57] C.-W. Tang and S.-F. You, “Using the technology of low temperature co-fired ceramic to design the dual-band bandpass filter,” IEEE Microw. Wireless Comp. Lett., vol. 16, no. 7, pp. 407-409, Jul. 2006.
[58] K.-C. Lin, C.-F. Chang, M.-C. Wu and S.-J. Chung, “Dual-bandpass filters with serial configuration using LTCC technology,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 6, pp. 2321-2328, Jun. 2006.
[59] C.-H. Huang, H.-C. Li, C.-H. Chen and T.-S. Horng, “Design of dual-band bandpass filter using compact spiral-shaped microstrip resonators,” in Proc. Asia Pacific Microw. Conf., 2008, pp. 1-4.
[60] H. Joshi and W. J. Chappell, “Dual-band lumped-element bandpass filter,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 12, pp. 4169-4177, Dec. 2006.
[61] 莊嘉成，三階交錯耦合微帶線帶通濾波器之研製，國立成功大學電機工程學系碩士論文，2002
[62] J.-C. Lu, C.-K. Liao and C.-Y. Chang, “Microstrip parallel-coupled filters with cascade trisection and quadruplet responses,” IEEE Trans. Microw. Theory Tech., vol. 56, no. 9, pp. 2101-2110, Sept. 2008.
[63] X. Guan, Z. Ma, P. Cai, G. Li, Y. Kobayashi, T. Anada and G. Hagiwara, “A dual-band bandpass filter synthesized by using frequency transformation and circuit conversion technique,” in Proc. Asia Pacific Microw. Conf., 2005, pp. 4.
[64] S. J. Lee and J. Y. Park, “PCB embedded 2.4GHz compact bandpass filter with two finite transmission zeros,” in Proc. Asia Pacific Microw. Conf., Dec. 2007, pp. 1-4.
[65] W.-S. Tung, Y.-C. Chiang and J.-C. Cheng, “A new compact LTCC bandpass filter using negative coupling,” IEEE Microw. Wireless Comp. Lett., vol. 15, no. 10, pp. 641- 643, Oct. 2005.
[66] Y.-C. Chen, L.-K. Yeh and H.-R. Chuang, “Direct synthesis of a bandpass filter with a controllable transmission zero,” in Proc. Asia Pacific Microw. Conf., Dec. 2010, pp. 1962-1965.
[67] Y.-Z. Wang, C.-A. Wang and K.-Y. Lin, “Miniaturized paralleled-coupled microstrip bandpass filters with spur-line for multi-spurious suppression,” in Proc. Asia Pacific Microw. Conf., 2007, pp. 1-4.
[68] Y. Sung, “Dual-mode dual-band filter with band notch structures,” IEEE Microw. Wireless Comp. Lett., vol. 20, no. 2, pp. 73-75, Feb. 2010.
[69] K. Liu, R. Frye and R. Emigh, “Compact balanced band pass filter for 3.3GHz – 3.9GHz WiMAX applications,” in Proc. Electron. Components and Technology Conf., 2009, pp. 599-1605.
[70] J.-M. Yook, J.-I. Yu, Y.-J. Kim and Y.-S. Kwon, “Integrated passive devices on the selectively anodized aluminum oxide,” in Proc. Eur. Microw. Conf., 2009, pp. 1654-1657.
[71] Y.-H. Jeng, S.-F. R. Chang, H.-K. Lin, “A high stopband-rejection LTCC filter with multiple transmission zeros,” IEEE Trans. Microw. Theory Tech., vol. 54, no. 2, pp. 633- 638, Feb. 2006.
[72] V. Novgorodov, S. Freisleben, J. Hornsteiner, M. Schmachtl, B. Vorotnikov, P. Heide and M. Vossiek, “Compact low-loss 2.4GHz ISM-band SAW bandpass filter on the LTCC substrate,” in Proc. Asia Pacific Microw. Conf., 2009, pp. 2072-2075.
[73] K. Zoschke, M. J. Wolf, M. Topper, O. Ehrmann, T. Fritzsch, K. Kaletta, F.-J. Schmuckle and H. Reichl, “Fabrication of application specific integrated passive devices using wafer level packaging technologies,”, IEEE Trans. on Advanced Packaging, vol. 30, no. 3, pp. 359-368, Aug. 2007.
[74] X.-H. Wu, Q.-X. Chu and L. Fan, “Compact dual-band bandpass filter with controllable bandwidths,” in Proc. Int. Conf. on Microw. and Millimeter Wave Technology, 2010, pp. 1305-1307.
[75] J. S. Hong and M. J. Lancaster, “Couplings of microstrip square open-loop resonators for cross-coupled planar microwave filters,” IEEE Trans. Microwave Theory Tech., vol. 44, pp. 2099–2109, Nov. 1996.
[76] 翁敏航，射頻被動元件設計，東華書局，2006
[77] 魏祖強，平面型變壓器為基礎之積體化被動元件設計與模型化研究，國立中山大學電機工程研究所碩士論文，2008。
[78] 蔡宛伶，以多模態級頻率轉換實現之多頻段濾波器與雙工器，國立台灣大學電機資訊學院電信工程學研究所碩士論文，2010。
[79] 李孝純，在有機基板實現耦合諧振器帶通濾波器之方法研究，國立中山大學通訊工程研究所碩士論文，2007。